MuskieFIRST | weight issues » Basement Baits and Custom Lure Painting

Muskie Discussion Forums

You are logged in as a guest. ( logon | register )

Random quote: "It's something they haven't seen before." -Hulbert trying to be nice about my lure selection.
- (Added by: kevin cochran)

Moderators: Slamr	View previous thread :: View next thread
Jump to page : 1 Now viewing page 1 [30 messages per page] More Muskie Fishing -> Basement Baits and Custom Lure Painting -> weight issues

Message Subject: weight issues

ericg0729

Posted 5/3/2013 7:10 AM (#638923)
Subject: weight issues

Posts: 43

Location: West Virginia

I am having trouble getting my baits weighed. I am using a digital caliper to measure the thickness of the lure. Then i divide in half. Set the caliper to the 1/2 thickness then make a mark with a pencil. Here is where i am having trouble. When i start to drill it i can never get it to drill dead center. i bought one of the dowling rod jigs but it is junk cause it will not auto center like it is suppose to. I also have a drill press that has a laser on it but dont have any way to hold the bait while drilling. This is the last step i am struggling with. Hope to get a few diffrent ways to do. Thanks in advance guys.

bowhunter29

Posted 5/3/2013 8:51 AM (#638939 - in reply to #638923)
Subject: Re: weight issues

Posts: 908

Location: South-Central PA

I use a small punch to mark the exact spot and then start with a very small drill bit. I then move up to the correct size bit and drill the final hole.

jeremy

MRichardson

Posted 5/3/2013 10:00 AM (#638963 - in reply to #638923)
Subject: RE: weight issues

I have these left over from the days I was on the bench as a moldmaker. They work nice because you can get your counter sink done at the same time as your drill starting hole. A punch like Jeremy said is probably the most practical. http://www.mcmaster.com/#combined-countersinks-and-drills/=ml8iml

Do you have a vice for your drill press? That would help hold things square. I have a cross slide vice mounted on mine; I find it very useful for many things. http://www.mcmaster.com/#cross-slide-vises/=ml8md6

Tackle Mechanic

Posted 5/3/2013 11:11 AM (#638980 - in reply to #638923)
Subject: RE: weight issues

Posts: 31

Use a brad point drill bit get mine at woodcraft works good

Beaver

Posted 5/3/2013 4:17 PM (#639047 - in reply to #638980)
Subject: RE: weight issues

Posts: 4266

I've been using a clamp on device that is used to drill holes for dowels, and it is dead nuts center every time. Fostner bits fit right through the holes and one side allows you to see the side of the lure, so that's where I do my marking. I'll have to see if I have a catalog with it still in it. I don't know why a doweling jig won't work for you, I'm looking at 2 in the Woodcraft catalog that came today. The only way to knock those off center is to overtighten them, then the adjustable side will cant a little bit, but I've never been off center, especially with Fostner bits, they have a little tit on the nose that sticks out to start the cut in the right spot. What kind of problems you having with the jig? Now I'm curious. You could always buy a small vise to set on the table of the drill press, then you could set the depth you wanted and repeat it.

Edited by Beaver 5/3/2013 4:33 PM

FUBAR

Posted 5/3/2013 6:39 PM (#639080 - in reply to #638923)
Subject: Re: weight issues

Posts: 216

Location: Middletown, Ohio

Good fostner bits and a drillpress vise is the way to go.

Mark

ericg0729

Posted 5/6/2013 4:03 PM (#639518 - in reply to #638923)
Subject: Re: weight issues

Posts: 43

Location: West Virginia

thanks for the awnsers guys. Is that the best way to find the center of the bait? Should i be marking the holes before or after shaping/ rounding the corners of the bait?

Jump to page : 1
Now viewing page 1 [30 messages per page]

Search this forum
Printer friendly version
E-mail a link to this thread