MuskieFIRST | Sealing Wooden Lures » Basement Baits and Custom Lure Painting

Muskie Discussion Forums

You are logged in as a guest. ( logon | register )

Random quote: "I have never caught a fish on that bait so you can have it"
- (Added by: Turkeyt)

Moderators: Slamr	View previous thread :: View next thread
Jump to page : 1 Now viewing page 1 [30 messages per page] More Muskie Fishing -> Basement Baits and Custom Lure Painting -> Sealing Wooden Lures

Message Subject: Sealing Wooden Lures

Decatur

Posted 5/21/2008 7:12 PM (#319118)
Subject: Sealing Wooden Lures

Posts: 82

What do you guys seal your lures with? I was thinking about using Propionate. Any opinions? TIA

woodieb8

Posted 5/21/2008 7:46 PM (#319119 - in reply to #319118)
Subject: Re: Sealing Wooden Lures

Posts: 1530

i prefer lacquer sandind sealer. some prefer the other

Decatur

Posted 5/21/2008 9:56 PM (#319135 - in reply to #319119)
Subject: Re: Sealing Wooden Lures

Posts: 82

woodieb8 - 5/21/2008 7:46 PM

i prefer lacquer sandind sealer. some prefer the other

Any particular brand?

knooter

Posted 5/21/2008 10:12 PM (#319139 - in reply to #319118)
Subject: Re: Sealing Wooden Lures

Posts: 531

Location: Hugo, MN

Deft Lacquer Sanding Sealer works well. I dunk the bait into the can and let it drip dry. I've used the propionate, too. If you go that route, use acetone to dissolve it. I used virgin laquer thinner and had issues getting it to dry clear. When I tried acetone, it worked much better. Both work well, just a matter of getting the sealer to soak into the grain.

woodieb8

Posted 5/22/2008 6:45 AM (#319164 - in reply to #319118)
Subject: Re: Sealing Wooden Lures

Posts: 1530

we use mcdonald and white. its based in windsor ontario. at less then 30 bucks a gallon its relarively cheep. dip each lure. everuthing is covered

Decatur

Posted 5/22/2008 2:04 PM (#319225 - in reply to #319164)
Subject: Re: Sealing Wooden Lures

Posts: 82

How many dips do you do?

Yake Bait

Posted 5/22/2008 8:46 PM (#319269 - in reply to #319118)
Subject: Re: Sealing Wooden Lures

Posts: 388

I have been using a pre coat of Devcon 2 ton epoxy. Sand lightly and paint on top of the pre coat. Works very well on maple and basswood lures. Cedar tends to bubble if you use too much heat so you need to be careful wiht that.

woodieb8

Posted 5/22/2008 9:38 PM (#319277 - in reply to #319118)
Subject: Re: Sealing Wooden Lures

Posts: 1530

we do 2 dips. it seals everything. remember to drill all holes and have your lip slot cut.. it hardens softer woods also. good luck

Decatur

Posted 5/22/2008 10:20 PM (#319283 - in reply to #319118)
Subject: Re: Sealing Wooden Lures

Posts: 82

Thanks for all of the replies guys!

Beaver

Posted 6/1/2008 1:26 PM (#320459 - in reply to #319283)
Subject: Re: Sealing Wooden Lures

Posts: 4266

I use Sherwin-Williams Barrier Coat. It's a polystyrene sealer and primer in one.
We used to use it at the water plant that I worked at to paint water pipes. It's designed to hold water in or out. It's not cheap and you have to use a mask in a ventilated area when you apply it. You could spray it or brush it, but I dip my lures. I'll hold them submerged for about 10-15 seconds and then hang them to dry. You can handle them in 4 hrs. but I normally hang them for a day and then go over them with fine steel wool and dip them again. When they are ready to go, it's like painting on an egg shell.
Best stuff I've ever used.
Beav

Decatur

Posted 6/1/2008 7:26 PM (#320488 - in reply to #319118)
Subject: Re: Sealing Wooden Lures

Posts: 82

Thanks!

Swede

Posted 6/4/2008 6:06 AM (#320847 - in reply to #319118)
Subject: Re: Sealing Wooden Lures

Posts: 50

I use propionate & i think its simple fast & good holds up to piketeeths good
Theres others on here that uses it too & i hope its due to how simple it is to use ,just dip&hang
Be aware that if you use a hard sealer (propionate) on soft wood it will be brittle .How do i know? Been there done that !!

Jump to page : 1
Now viewing page 1 [30 messages per page]

Search this forum
Printer friendly version
E-mail a link to this thread